Lube for gears etc.
 Views: 2473
 Comments: 4
Posted by Crewella
 Apr 07, 2012
|
Beta's tail
Views: 1986
Posted by Crewella
Mar 01, 2012
|
Beta's tail
Views: 1996
Posted by Crewella
Mar 01, 2012
|
Beta's tail
Views: 1990
Posted by Crewella
Mar 01, 2012
|
Beta's tail
Views: 1980
Posted by Crewella
Mar 01, 2012
|
Beta's tail
Views: 1994
Posted by Crewella
Mar 01, 2012
|
Beta's tail
Views: 1917
Posted by Crewella
Feb 29, 2012
|
Beta's tail
Views: 1951
Posted by Crewella
Feb 29, 2012
|
Note: RB sensors are now cove…
Note: RB sensors are now covered in a layer of plastic
Views: 1989
Posted by Crewella
Mar 03, 2012
|
Once it's all threaded though…
Once it's all threaded though and in position ...... you can start putting it all back again!
Views: 2225
Posted by Crewella
Feb 27, 2012
|
Side view of threaded cable ge…
Side view of threaded cable gear.
Views: 2289
Posted by Crewella
Feb 27, 2012
|
Close-up for orientation
Views: 2237
Posted by Crewella
Feb 27, 2012
|
The housing cover - one gear s…
The housing cover - one gear stayed with it.
Views: 2325
Posted by Crewella
Feb 27, 2012
|
With the housing turned back t…
With the housing turned back the right way and the cover removed, you have access to the gears.
Views: 2333
Posted by Crewella
Feb 27, 2012
|
Closer view of underside of si…
Closer view of underside of side cable housing.
Views: 2183
Posted by Crewella
Feb 27, 2012
|
Side cable housing should lift…
Side cable housing should lift up and flip over to give you access to the housing screws underneath.
Views: 2425
Posted by Crewella
Feb 27, 2012
|
One more screw to release the…
One more screw to release the side cable housing.
Views: 2441
Posted by Crewella
Feb 27, 2012
|
You'll need to undo the orange…
You'll need to undo the orange tab (pot/position sensor)
Views: 2618
Posted by Crewella
Feb 27, 2012
|
Pic of the terminals the cable…
Pic of the terminals the cables need to be reattached to.
Views: 2379
Posted by Crewella
Feb 27, 2012
|
The two cables are (thankfully…
The two cables are (thankfully) held together further down
Views: 2344
Posted by Crewella
Feb 27, 2012
|
One out .... one to go.
Views: 2243
Posted by Crewella
Feb 27, 2012
|
Once the top cable housing it…
Once the top cable housing it pullled up, you will also need to disconnect these two cables.
Views: 2179
Posted by Crewella
Feb 27, 2012
|
Right front leg comes off in t…
Right front leg comes off in the same way as the left, to access this screw
Views: 2295
Posted by Crewella
Feb 27, 2012
|
Another screw for the housing…
Another screw for the housing under the left front leg
Views: 2367
Posted by Crewella
Feb 27, 2012
|
Behind the left front leg, you…
Behind the left front leg, you can access the screws to release the housing
Views: 2268
Posted by Crewella
Feb 27, 2012
|
You need to pull the whole leg…
You need to pull the whole leg away from the body to access the screws to release the side cable housing
Views: 2446
Posted by Crewella
Feb 27, 2012
|
To access the housing for the…
To access the housing for the side cables, you need to remove the upper leg cover.
Views: 2341
Posted by Crewella
Feb 27, 2012
|
With the motor pulled away, th…
With the motor pulled away, the gears will move the full extent of their run.
Views: 2333
Posted by Crewella
Feb 27, 2012
|
The back cover taken off the t…
The back cover taken off the top cable gear housing, you can then pull the motor out.
Views: 2419
Posted by Crewella
Feb 27, 2012
|
How the C-shaped guide fits in…
How the C-shaped guide fits into the housing.
Views: 2216
Posted by Crewella
Feb 27, 2012
|
The C-shaped piece that hold t…
The C-shaped piece that hold the wires in position as they cross.
Views: 2272
Posted by Crewella
Feb 27, 2012
|
Step 3: Wrap the cable right b…
Step 3: Wrap the cable right back around and hold in place (its harder than it sounds!)
Views: 1978
Posted by Crewella
Feb 21, 2012
|
It should look like this:
It should look like this:
Views: 1803
Posted by Crewella
Feb 21, 2012
|
Step 2: Wrap the cable towards…
Step 2: Wrap the cable towards the rear of the gear and overlap them.
Views: 1842
Posted by Crewella
Feb 21, 2012
|
Rethreading the cable gear ste…
Rethreading the cable gear step 1: Thread the cable through the gear, this part is very fiddly. Make sure you have half the cable coming out each side.
Views: 1884
Posted by Crewella
Feb 21, 2012
|
A closer look at the main gear…
A closer look at the main gear:
Views: 1778
Posted by Crewella
Feb 21, 2012
|
This bottom gear is where the…
This bottom gear is where the cable attaches to, please note very carefully the position of the gear as you remove it, or use here for a reference.
Views: 1863
Posted by Crewella
Feb 21, 2012
|
The other side of the gear hou…
The other side of the gear housing.
Views: 1855
Posted by Crewella
Feb 21, 2012
|
Underneath the gear housing, i…
Underneath the gear housing, inside the body cavity, showing where the bottom cable feeds through, note it also has a spring that it must run through.
Views: 1920
Posted by Crewella
Feb 21, 2012
|
The gear housing lifted out of…
The gear housing lifted out of the body cavity, DO NOT PULL IT RIGHT OUT! Leave the wires attached. You will need to undo the three screws during the operation.
Views: 1967
Posted by Crewella
Feb 21, 2012
|
